STABILIZED POWER SUPPLY 3 30 V 2 5 A

This is a versatile power supply that will solve most of the supply problems arising in the everyday work of any electronics workshop. It covers a wide range of voltages being continuously variable from 30 V down to 3 V. The output current is 2.5 A maximum, more than enough for most applications. The circuit is completely stabilised even at the extremes of its output range and is fully protected against short-circuits and overloading.

Circuit Diagram

Working

The power supply is using a well known and quite popular VOLTAGE STABILIZER IC the LM 723. The IC can be adjusted for output voltages that vary continuously between 2 and 37 VDC and has a current rating of 150 mA which is of course too low for any serious use. In order to increase the current handling capacity of the circuit the output of the IC is used to drive a darlington pair formed by two power transistors the BD 135 and the 2N 3055. The use of the transistors to increase the maximum current output limits the range of output voltages somewhat and this is why the circuit has been designed to operate from 3 to 30 VDC. The resistor R5 that you see connected in series with the output of the supply is used for the protection of the circuit from overloading. If an excessively large current flows through R5, the voltage across it increases and any voltage greater than 0.3 V across it has as a result to cut the supply off, thus effectively protecting it from overloads. This protection feature is built in the LM 723 and the voltage drop across R5 is sensed by the IC itself between pins 2 and 3. At the same time the IC is continuously comparing the output voltage to its internal reference and if the difference exceeds the designer’s standards it corrects it automatically. This ensures great stability under different loads. The potentiometer P1 is used to adjust the out put voltage at the desired level. If the full range from 3 to 30 V is desired then you should use a mains transformer with a secondary winding having a rating of at least 24 V/3 A. If the maxi mum voltage output is not desired you can of course use a transformer with a lower secondary voltage output. (However, once rectified the voltage across the capacitor C2 should exceed by 4-5 volts the maximum output expected from the circuit.

Parts List

Resistors

R1 = 560R 1/4W

R2 = 1,2 K 1/4W

R3 = 3,9 K 1/4W

R4 = 15K 1/4W

R5 = 0,15R 5W 

Capacitors

C1 = 100nF

C2 = 2200uF 35-40V

C3 = 100 pF

C4 = 100uF/ 35V

Miscellaneous

D = B40 C3300/2200, 3A Rectifier Bridge

P1 = 10K Potentiometer

TR1 = BD 135

TR2 = 2N3055

IC = LM723

BD 135

2N3055

LM723

Read More

LM3940 1A Low Dropout Regulator for 5V to 3.3V Conversion

LM3940 1A Low Dropout Regulator for 5V to 3.3V Conversion

General Description :
The LM3940 is a 1A low dropout regulator designed to provide 3.3V from a 5V supply.
The LM3940 is ideally suited for systems which contain both 5V and 3.3V logic, with prime power provided from a 5V bus.
Because the LM3940 is a true low dropout regulator, it can hold its 3.3V output in regulation with input voltages as low as 4.5V.
The T0-220 package of the LM3940 means that in most applications the full 1A of load current can be delivered without using an additional heatsink.
The surface mount TO-263 package uses minimum board space, and gives excellent power dissipation capability when soldered to a copper plane on the PC board.

Features
■ Output voltage specified over temperature
■ Excellent load regulation
■ Guaranteed 1A output current
■ Requires only one external component
■ Built-in protection against excess temperature
■ Short circuit protected
Applications
■ Laptop/Desktop Computers
■ Logic Systems

Typical Application

Connection Diagram

Read More